Cheese board for a house divided
Furnished content. (from Lumberjocks.com)
This is a serving board for a couple who are college sports fans, but went to different schools. On the one side, is the University of South Carolina. On the other side is the Ohio State University. The school stripes are made of wenge, maple, and bloodwood. Both of them work with animals at the National Zoo, so the main part of the board was made of zebrawood. It is finished with a food safe finish of mineral oil and bees wax.
Read more here
posted at: 12:00am on 06-Feb-2021 path: /Woodworking | permalink | edit (requires password)
Jewelry box for Valentines day.
Furnished content. (from Lumberjocks.com)
Made with flamed Maple and inlay of Cherry. Cherry also used for the feet. 11 1/2” wide x 6 11/2” deep x 7” tall. Top, sides, drawer fronts and dividers all 3/8” thick. Drawer sidesand drawer bottoms are 1/8” thick. The drawers are lined with dark green flocking. Small brass hinges for the top and a ball chain for the restraint. Simple build, easy inlay using Bosch colt to cut inlay grooves with 1/16' Freud bit. Finish is wipe on poly, several coats and then waxed and buffed. This is one of 4. One for wife, daughter, granddaughter, and daughter-in-law.
Read more here
posted at: 12:00am on 06-Feb-2021 path: /Woodworking | permalink | edit (requires password)
Woodworker's Drill Press
Furnished content. (from Popularwoodworking.com)
Tool: Laser Drill Press Buy Now Manufacturer: Delta Delta's 18″ drill press is specifically designed for woodworking. The difference is in the table: It's a big improvement over the tables designed for metalworking on most drill presses. First off, …Source
Read more here
posted at: 12:00am on 06-Feb-2021 path: /Woodworking | permalink | edit (requires password)
Knockdown Computer Desk
Furnished content. (from Popularwoodworking.com)
Ladders form the base of this knockdown desk simple steps to a higher education in woodworking. Editor's Note: Hunter was a high school senior when he completed this article for Popular Woodworking in 2009. I'm in the …Source
Read more here
posted at: 12:00am on 06-Feb-2021 path: /Woodworking | permalink | edit (requires password)
Simple Reliable Sliding Dovetail Guide
Furnished content. (from Lumberjocks.com)
For the past 20ish years I have challenged to make stuff with wood that does not require screws or nails. It's just a mental challenge I enjoy. Dovetails, mortise and tenons, and sliding dovetails are my friends in this challenge. The problem is, sliding dovetails are usually a pain to get right and they are not very forgiving if I make a mistake.That changed when it hit me that a simple guide rail cut with a dovetail bit at the exact same depth as the thickness of the guide(photo 1 and 2), will create a profile (housing) that exactly lines up with the wide part of the dovetail at ANY depth needed (see red lines in photo 3). So I made two identical guide rails using the same bit that I make the dovetail with. The finished project here is the pair of guides. Each made from 1/4” thick plywood base and a plywood (thickness not critical) rail with a straight edge for the router to ride along.With a pair of these guides, the process of making the sliding dovetail is pretty simple and reliable.1. Use the dovetail bit to cut the long dovetail. It does not matter if the dovetail is tapered or the same width throughout. Can be done with handheld router or a router table. 2. (Photo 4) Position the first guide rail on the wood where you need to cut the dovetail housing and clamp it in place good. It must not move. 3. (photo 5) Position the dovetail board you made in step 1 firmly against the guide rail in the position that you need the board to end up. 4. (photo 5) Push the other guide rail firmly against the other side of the dovetail and clamp it firmly in place. 5. (photo 6) Slide the dovetail board the end being careful not to shift the guides. Then set your router to the depth of dovetail PLUS the thickness of the base of the guide. And run it along the left guide, then run it back along the right guide (this avoids a climbing cut) The housing matches the dovetail exactly. If you set the depth right, it will be a perfect fit.Super simple game changer if you use sliding dovetails for shelves or battens.source: More photos and build description of simple sliding dovetail jig.
Read more here
posted at: 12:00am on 06-Feb-2021 path: /Woodworking | permalink | edit (requires password)
Promoted by Feed Shark
|
|