The Woodshop Shed

adventures in woodworking and home maintenance, from my shop in an oversized backyard shed

August 2022
Sun Mon Tue Wed Thu Fri Sat
 
     


Three way Highchair

Furnished content.
(from Lumberjocks.com)


Three way HighchairYes this is just a put together these by another plan but I did add the top tray as I felt it added to the use.Link for the plans is here : https://www.gcwoodworks.com/shop/the-baby-sitter-woodworking-plans/I used some 3/4 cherry on the first and 3/4 pine on the second one both felt sturdy when fully glued.
The first one was quite bit heavier and stained little darker with different wood used.I also added straps at the seat here : https://www.ebay.com/itm/165476418298Have wanted to do one of these for a while and my wife pushed me to build two.Last picture is my templates so I can build future ones without recreating from scratch , all other seat panels are pretty much square cuts.My young cousins loved them

Read more here


posted at: 12:00am on 01-Aug-2022
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Time tested job stools

Furnished content.
(from Lumberjocks.com)


Time tested job stoolsI made these in 1979 after seeing something similar while driving by some working carpenters. They have been in use ever since and have worn down and inch from being slid around on concrete, etc.. The height is good for reaching 8' ceilings and can also be stacked for 12”, 24”, and 32”. Often used for blocking & lifting heavy stuff, as a saw bench, to hold upper kitchen cabinets, & as a place to sit for lunch. Hammer claw fits in the hole to pick up & carry, sometimes used upside down to hold a spool of wire, & occasionally as a crate. One suffered a broken leg in a fall but eventually had the piece replaced.A year or two ago I was given some plywood scraps & made four more, thinking I might sell them, but they have been put to use as well. If you make some, the sequence is to cut the pieces square, taper the legs, leaving an inch or two straight at the bottom, cut the notches in the tapered legs, fit the sides with the short point even with the top of the legs, & belt sand flat after. Round the edges of the top before fastening to avoid hitting the fasteners. Thin nails are better than screws to not split the plywood- gun nails or staples would be fine. Both the new & old ones have had multiple coats of linseed oil, especially soaking the end grain of the feet.I wrote my name and the date inside of one, & that is how I remember the year that I started my business.Cheers, Jay

Read more here


posted at: 12:00am on 01-Aug-2022
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



August 2022
Sun Mon Tue Wed Thu Fri Sat
 
     


Promoted by Feed Shark





RSS (site)  RSS (path)

ATOM (site)  ATOM (path)

Categories
 - blog home

 - Announcements  (0)
 - Annoyances  (0)
 - For_Sale  (0)
 - Home_and_Garden  (1)
 - Humor  (0)
 - Industry_News  (0)
 - Massachusetts_USA  (0)
     - Swansea  (0)
 - Notices  (0)
 - Observations  (0)
 - Oddities  (0)
 - Privacy  (1)
 - Reading  (0)
     - Books  (0)
     - Ebooks  (0)
     - Magazines  (0)
     - Online_Articles  (0)
 - Reviews  (1)
 - Rhode_Island_USA  (0)
     - Providence  (0)
 - Shop  (0)
     - Planes  (1)
 - Shop_Improvements  (2)
 - Woodworking  (6966)
     - Calculator  (1)
     - Projects  (2)
     - Resources  (3)
     - Techniques  (0)
     - Tips  (0)
     - Videos  (7)


Archives
 -2024  December  (3)
 -2024  November  (11)
 -2024  October  (11)
 -2024  September  (13)
 -2024  August  (13)
 -2024  July  (11)
 -2024  June  (9)
 -2024  May  (10)
 -2024  April  (9)
 -2024  March  (14)
 -2024  February  (15)
 -2024  January  (21)
 -2022  October  (2)
 -2022  September  (86)


My Sites

 - Millennium3Publishing.com

 - SponsorWorks.net

 - ListBug.com

 - TextEx.net

 - FindAdsHere.com

 - VisitLater.com