The Woodshop Shed

adventures in woodworking and home maintenance, from my shop in an oversized backyard shed

November 2026
Sun Mon Tue Wed Thu Fri Sat
         


what are the post brackets for?

Furnished content.
(from WoodNet.net)


My 40x56 pole barn was built some 30+ years ago. The posts go into the ground and there's a 5" monolithic slab inside. The posts have these brackets at the base and I don't know why. If they were there to help hold up the post, that doesn't look like what they are doing as most/all are lifted a little bit like this one. Either it was miss-aligned when installed, or the post lifted. Either way I can't tell which and there aren't any obvious signs of movement such as the barn eve or walls having any high and low spots. Maybe these were installed as part of the concrete pour for some reason unbeknownst to me.
Any ideas?

I removed the bracket temporarily just to see if there was anything noteworthy underneath it, but I put it back on.

.png  IMG_2869_25P.png (Size: 95.14 KB / Downloads: 63)

.png  IMG_2872_25p.png (Size: 100.96 KB / Downloads: 60)

Read more here


posted at: 12:00am on 17-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Bora Centipede Work Stand

Furnished content.
(from WoodNet.net)


Anyone have one of these? I am considering one for use with my Tracksaw. I saw them at Woodworkers Source and am intrigued.

Any thoughts are appreciated.

Read more here


posted at: 12:00am on 17-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



crosscut sled

Furnished content.
(from WoodNet.net)


I made 1 for myself a few years ago, sold it with my shop. Now I need another. I basically just want to make sure my plywood panels are square. I've looked on You Tube, didn't really see anything I like. Found a simple one in Woodsmith #73. What's the suggested way to ensure the support bar is square?

Read more here


posted at: 12:00am on 17-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Any 3D printer guys on here? Need jointech part

Furnished content.
(from WoodNet.net)


Hey guys, it has been a looong time since I posted. Anyone on here do 3d printing that might be interested in printing a dustport for the jointech router table fence-it broke during my latest move. Or could point me in the right direction? Thanks ROB

Read more here


posted at: 12:00am on 13-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



What happened to the interface?

Furnished content.
(from WoodNet.net)


Where did the features go for posting photos, links, etc?

John

Read more here


posted at: 12:00am on 08-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



identificationof tools in a catalog

Furnished content.
(from WoodNet.net)


I've got a project I'm working on. There are grooves in some of the pieces of the item I'm working on. The grooves extend to the end of the piece and are only 2 to 3 inches in length, not extending to the other end of the piece. I need to deepen the grooves a small amount, and lengthen them about half an inch. The grooves are almost a quarter of an inch, 0.235 inches wide.That pretty much rules out use of a 1/4" chisle I have. Checkikng the width with a metric caliper, I found they're very close to 6mm in width. Went through the list of metric chisles offered by Amazon, and found a set of 4 chisles at an affordable price, and ordered the set. When they arrived, I figured I could proceed with the project, only to discover that the new "6mm" chisle is a quarter of an inch wide, 6.7mm. Checked the other chisles in the set, and they're all standard American widths, although the tools themselves are clearly marked with metric width. Back to the Amazon web site, and discovered listings that had text stating tool as fraction of an inch in width, and pictures of the chisles showing metric markings. And some of the listings are really confusing, showing the width as "6mm - 1/4 inch", leaving one to wonder what the width of the chisle actually is. I tried quering the online help, only to get the advice that if the width is critical I should measure the tool. Big help. So I tried going in person to some potential stores with my measujring device. A potential purchase was marked as to the size, but it was packaged such that it would have to be opened to measure the tool, and not all stores allow that. I finally ended up ordering a mortice chisel from Amazon that clearly states 6mm width in both text and picture. It's due to arrive on Sundy, so I'll fid out then if it's really the tool I need.

.jpg  100_9047.jpg (Size: 745.31 KB / Downloads: 45)

Read more here


posted at: 12:00am on 08-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Conduit for workshop electric

Furnished content.
(from WoodNet.net)


I'm going to use conduit to run receptacles in my workshop (24'x40') for the flexibility for present and future design changes in the workshop.
With that said, there's options for metal or pvc conduit. It's kinda a toss-up to me.
I'm only running about 150' of it, so the actual dollar difference between the two is not an issue to me. Another idea is to run armored clad wire. Less work and even less cost overall.
I'm planning on running these in low risk areas - meaning like behind base cabinets or just under the overhead cabinets, but some length of it will be exposed in some areas.

I know to not run regular romex through conduit.

Any suggestions on installing conduit or clad?
What would be your approach and why?
thanks!

Read more here


posted at: 12:00am on 05-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Hello from a new member

Furnished content.
(from WoodNet.net)


Hello everyone, I've been lurking on the forums for a little while reading through old threads and finally decided to create an account. I'm a hobbyist woodworker mostly focused on small furniture projects and trying to incorporate more hand tools into my workflow lately. Looking forward to learning from everyone here and contributing to the discussions.

.jpeg  IMG_3012 (1).jpeg (Size: 169.99 KB / Downloads: 79)

Read more here


posted at: 12:00am on 05-Nov-2026
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



November 2026
Sun Mon Tue Wed Thu Fri Sat
         


Promoted by Feed Shark





RSS (site)  RSS (path)

ATOM (site)  ATOM (path)

Categories
 - blog home

 - Announcements  (0)
 - Annoyances  (0)
 - For_Sale  (0)
 - Home_and_Garden  (1)
 - Humor  (0)
 - Industry_News  (0)
 - Massachusetts_USA  (0)
     - Swansea  (0)
 - Notices  (0)
 - Observations  (0)
 - Oddities  (0)
 - Privacy  (1)
 - Reading  (0)
     - Books  (0)
     - Ebooks  (0)
     - Magazines  (0)
     - Online_Articles  (0)
 - Reviews  (1)
 - Rhode_Island_USA  (0)
     - Providence  (0)
 - Shop  (0)
     - Planes  (1)
 - Shop_Improvements  (2)
 - Woodworking  (449)
     - Calculator  (1)
     - Projects  (2)
     - Resources  (3)
     - Techniques  (0)
     - Tips  (0)
     - Videos  (0)


Archives
 -2026  November  (8)
 -2026  October  (11)
 -2026  September  (13)
 -2026  August  (12)
 -2026  July  (12)
 -2026  June  (10)
 -2026  May  (10)
 -2026  April  (12)
 -2026  March  (11)
 -2026  February  (16)
 -2026  January  (15)
 -2025  December  (15)
 -2025  November  (5)
 -2025  October  (17)


My Sites

 - Millennium3Publishing.com

 - SponsorWorks.net

 - ListBug.com

 - TextEx.net

 - FindAdsHere.com

 - VisitLater.com