The Woodshop Shed

adventures in woodworking and home maintenance, from my shop in an oversized backyard shed

July 2019
Sun Mon Tue Wed Thu Fri Sat
 
     


mixed hardwood coffee table

Furnished content.
(from Lumberjocks.com)


mixed hardwood coffee tablehere is my mixed hardwood coffee table I just finished its made from left over cherry hickory ash and red oak I had left over from making my full size bed frame its finished with a boiled linseed oil finish it was made using kreg screws for all the construction hope you enjoy



Read more here

posted at: 12:00am on 31-Jul-2019
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



Laundry Hamper

Furnished content.
(from Lumberjocks.com)


Laundry HamperI made this cherry laundry hamper for my kids at the request of my wife. It features curved rails and book-matched panels. The side rails are lower and the bottom has holes in order to facilitate air flow to clear out the funk.I filmed the build and you can view it here if you'd like:
http://www.garagewoodworks.com/video.php?video=245Subscribe on YouTube



Read more here

posted at: 12:00am on 31-Jul-2019
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



End vise anti-racking jig

Furnished content.
(from Lumberjocks.com)


End vise anti-racking jigI'm posting this as an easy possible solution for those that use their end vise to either clamp a component on one side, or as I do – clamp along the from edge of the bench for sticking molding or planing long narrow boards. Hopefully this will benefit some others, especially if there is no wagon vise.Picture two shows all the needed materials I used: a 1/4” poplar dowel, a 3/4” oak dowel, a small block of cherry to be used for center drilling the oak dowel, and a block of hard maple to extend my vise jaw.Picture 3 shows a dowel drilling block as described somewhere on the web, can't remember where I saw it, but basically: I drilled a 3/4” hole through the block for the larger dowel, and a 1/4” hole – centered on the first & on the top, to guide the drill bit to the center of the larger dowel.Number 4 picture shows the drilled dowel & centering block.Picture 5 shows the drilling spacing on the dowel. I used 1/4” holes with 1/4” between the circumferences or edges of the holes – which equals 1/2” center to center. Then I drilled another series of holes directly in between the first set, at 90 degrees from the first. This yields 1/4” increments for rack adjustments. So far I have found this to be sufficient to my needs, with some experimentation yielding a maximum vice rack or distortion at about 1/8”.
If this is too course for others, I believe that the oak dowel can be drilled three ways or directions, by rotating 60 degrees each time, to yield much closer spacing. I've not attempted this though.Picture 6 shows how the dowel will resist against the added maple block, in my case. This was only done because I have no space to drill a 3/4” hole directly behind the jaw due to the factory screws between each of the stabilizers and the adjustment screw, as shown in this photo from below the bench:
As for the oak dowel, I made it long enough to reach as far as possible when in & flush with vise face, with drilling enough quarter inch holes to permit use with the vise open as far as it goes. Opening or extracting the dowel when in flush is very easy by reaching under the bench, it is very loose in the hole, but stable due to the length – it doesn't fall out.Also, needing some lather time, I decided to make a pin to replace the dowel, with a cap copied from a brass adjustment screw from my antique plow plane.
Time has shown this set up to work very well, and the pin allows a great deal of vise pressure to be applied, with the pin exposed top & bottom of the dowel. The shearing force to break it is much greater than any I've applied. I have clamped a 3/8” board at about 24” long on the front of the bench between the vise dog & a bench dog to the point where it bowed up.Hopefully this will benefit someone else, and should there be any questions, please contact me.



Read more here

posted at: 12:00am on 31-Jul-2019
path: /Woodworking | permalink | edit (requires password)

Comments:
0 comments, click here to add the first



July 2019
Sun Mon Tue Wed Thu Fri Sat
 
     


Promoted by Feed Shark





RSS (site)  RSS (path)

ATOM (site)  ATOM (path)

Categories
 - blog home

 - Announcements  (0)
 - Annoyances  (0)
 - For_Sale  (0)
 - Home_and_Garden  (0)
 - Humor  (0)
 - Industry_News  (1341)
 - Massachusetts_USA  (0)
     - Swansea  (0)
 - Notices  (0)
 - Observations  (0)
 - Oddities  (0)
 - Reading  (0)
     - Books  (0)
     - Ebooks  (0)
     - Magazines  (0)
     - Online_Articles  (0)
 - Reviews  (0)
 - Rhode_Island_USA  (0)
     - Providence  (0)
 - Shop  (0)
 - Shop_Improvements  (2)
 - Woodworking  (3272)
     - Projects  (1)
     - Resources  (3)
     - Techniques  (179)
     - Tips  (0)
     - Videos  (7)


Archives
 -2019  December  (44)
 -2019  November  (89)
 -2019  October  (89)
 -2019  September  (90)
 -2019  August  (92)
 -2019  July  (94)
 -2019  June  (89)
 -2019  May  (97)
 -2019  April  (89)
 -2019  March  (100)
 -2019  February  (93)
 -2019  January  (88)
 -2018  December  (28)


My Sites

 - Millennium3Publishing.com

 - SponsorWorks.net

 - ListBug.com

 - TextEx.net

 - FindAdsHere.com

 - VisitLater.com