The Woodshop Shed

Box Clock or Clock Box?

Furnished content.
(from Lumberjocks.com)


This is a box clock (or maybe a clock box) I completed today.
11”x9”x4”
Canary-wood & Cherry with 7 coats of lacquer.

Comments:
0 comments, click here to add the first

Rocking Chair Prototype

Furnished content.
(from Lumberjocks.com)


I've had the opportunity to build 8 of the Hal Taylor-design classic rocking chairs, and then left behind rockers for perhaps 5 years now. Several contemporary desks and side tables later, I wanted to revisit the rocking chair from a different, non-classical, perspective.This is a prototype, and while I started with a full-scale drawing of a rocking chair, the end-result bears little resemblance to the original design. As everyone knows, design-while-building is both fascinating and frustrating.
For those interested in the general design, I'll offer that this is a very buildable chair, based on templates and common tools; the challenges arise in precise layout and execution, and maintaining a holistic sense of how the parts interact with each other: one example (we're getting ahead of ourselves here) – the Lower Cross Member (below the Seat) must remain square to the Front Cross Member, and everything in-between must also be square and align properly) the challenges are subtle and demanding.Design Considerations
This design departs from virtually every convention I know, except for the Rocker Rails which are necessary for it to be a rocking chair: the back has no fixed support, no legs to speak of, and I substituted sliding dovetails for the traditional Maloof/Taylor joinery.Touching on each of these points:The floating back is carried forward from my High Back Chair (see my Projects section, here), and relies on the Back Braces being captured in a loose deep mortise, at the base of the 'seat', and the top being captured by a moveable Crest Rail.Sliding dovetails streamline the otherwise bulky Maloof/Taylor joint for the Arms/Front Risers/Front Verticals (legs, if you will). The traditional joint is beautiful when used in a classic design; but out of place within contemporary chairs.An under-seat 'back riser' arrangement supports the seat these streamline the sides of the chair, and are sized to be the primary load-carrying element - I'll re-visiting the ones used here, as their shape is my least favorite aspect of the chair.The chair tapers 3 degrees front-to-back, which creates different sized cross-members (Front, Lower and Rear End Cap).A final note on visual weight: this design places considerable physical and visual weight on the front half of the chair: the Front Risers, the large end of the Rails and the full weigh of the arms. This required the addition of the Rear Cap - to offset the otherwise front-end load of the parts, as well as to draw the eye along the full profile - it would not work to have so much going on forward of center, and nothing but thin sticks behind center.Wood Selection
From prior builds, I had sufficient Cherry in the shop to complete the build. Billets for each piece begin life at 6/4, and are 5/4+ finished - the Rails are an exception, as I start at 8/4, and finish at 6/4+.Build Approach
I work from templates whenever possible: these allow standardized parts, and design changes are first made to the templates, and the parts remade.Festool Dominos are my go-to joinery application, and these are used for several of the joints; however, I found these to be problematic when first connecting the Rails, Front Verticals and Arms I substituted sliding dovetails to spread the load across the joints - I made these exposed, rather than blind, for aesthetics, and practiced a great deal prior to making the cuts on 'good billets' (having said this, I still need more practice).
Seat Support (Back Risers)I went through several profiles on the Back Risers prior to settling on the ones used I need to revisit these - my daughter says she likes them though, I'm not sure that she's an un-biased critic.Floating Back
I first incorporated the Floating Back in my High Back Chair. The design premise is that the Back Brace bottoms are angled (30 degrees) into individual deep mortises (in the seat), and are held in place by the pressure of the sitter's weight. The floating Back Braces have both considerable flex front-to-back, and are constrained by the Crest Rail. This approach creates a very comfortable envelope for the sitter.Transition Block (Seat)
The Seat comprises two parts: Seat Slats (5 one-eighth inch x 18 slats bent and glued via a form) and the Transition Block - this piece receives both the back end of the Seat Slats and bottoms of the Back Braces the piece serves to transition the visual line from the Seat Front to the top of the Back Braces (these elements are aligned to help support this).The mortises are cut using a trammel router jig - typically, I'll use a 35 to 38 radius - both the Transition Block and the Crest Rail need to be made using the same radius.Crest Rail
The Crest Rail is comprised of 8 blocks of glue-up mirror dados, which is then shaped via a compound arc: 35-38 front-to-back, and 41-45 top-to-bottom. The Crest Rail is made by ripping a 2 thick, 5 wide board on the bandsaw; these haves are cleaned on the jointer, and thicknessed on the planer. Dado locations are marked such that 5/16 is removed from each side in matched pairs (for 8 slots - one for each Back Brace. The two haves are glued together to create 8 through mortises. Individual blocks are then cut to separate the mortised pieces. These pieces are then mitered at 3 degrees on each side; then glued to form the desired arc. (there is considerable math behind this Once all eight pieces have been glued, the appropriate horizontal (front-to-back) arc is formed then draw the desired vertical (top -to-bottom) arc, and cut on the bandsaw.As I stated at the outset this is a prototype with the primary purpose to assess proportions and workflow. The fact that the design changed during the build means that I may need to build another chair to lock down all of the variables.Local feedback has been interesting my sister and daughter find it very comfortable; my wife is not a fan of contemporary designs and she'd be happy if I just sold my equipment and took-up a different interest and so it goes.I have not applied a finish to this chair; as I have to attend to other things for several weeks. When I do get to the finishing stage, I will use 2 coats of Zinsser Seal Coat (or Deft Lacquer Sealer) and several coats of Deft Clear Acrylic Wood Finish.As always, I'm look forward to comments and constructive feedback; and I'll try to answer questions as thoroughly as is practicable.
Everyone, Stay Safe and Chill-out (man, things have become tense out there).

Comments:
0 comments, click here to add the first

New Design Wall Clock

Furnished content.
(from Lumberjocks.com)


In the past, I did a wall clock that had more of a star shape, and I really liked the look:However, the circles made for little gluing surface (and were a pain to assemble… next time I'll use dowels!). In fact, this clock is so fragile that I've decided to keep it for myself.But, I liked the star shape of it, so I decided to try it again. I ended up using the last of my 1.5” Ambrosia Maple (at least the AM with any fun grain to it). This design gives much more surface to glue, and overall it feels pretty sturdy. I wasn't able to get the miters perfect (the angle pieces were almost impossible to clamp), but overall I was pretty pleased with the look.It's about 14 inches tall and 11 inches across.Rummaging through my scrap burl box, I stumbled on a piece that I felt made a perfect centerpiece. It's finished in a wipe-on gloss poly with two different color end caps on the ends of the “spokes.”

Comments:
0 comments, click here to add the first

Case Modern EDC Knives Review

Furnished content.
(from Popularwoodworking.com)


The new Marilla and Kinzua are great EDC knives for woodworkers. Tool: Marilla Shop Now and Kinzua Shop Now  Manufacturer: Case Knives MSRP:$164.99 (Marilla) & $139.99 (Kinzua) No tool in my shop gets more usage than my everyday …Source

Read more here

Comments:
0 comments, click here to add the first

Modern 12 Drawer Dresser

Furnished content.
(from Popularwoodworking.com)


A master craftsman's method for making perfectly spaced drawers. I made this dresser for a client whose father designed and built similar furniture back in the 1950s. Its grid system is very modern looking, but getting all the spacing just …Source

Read more here

Comments:
0 comments, click here to add the first