The Woodshop Shed

Modern Sideboard with Aluminum Accents

Furnished content.
(from Lumberjocks.com)


My wife and I designed, and I built, this sideboard for our kitchen, which is in the final stages of a remodel. We won't use it to hold dishes or serve food. Instead, we'll store cookbooks in the main cavity, office supplies in the drawers, receipts, menus, and working papers in desk trays in the open cubby, and odd and ends wherever they will fit.Aside from the storage requirements, my wife wanted the visible edges on the front of the sideboard to be thin to give it a more refined, less chunky appearance.The sideboard will be located along a short wall near the opening to our family room, so it needed to be as narrow as possible while remaining practical. Overall, it's 42 wide, 32 high (not including the 6 legs), and 13 1/2 deep.For the finish, we opted for paint even though I really, really dislike painting. (I don't have a sprayer, and I always struggle to achieve a smooth, even finish.) We tested a few paint types and settled on General Finishes Milk Paint in Queenstown Gray. Internet sources vary on whether a topcoat is needed. I didn't topcoat it, so I hope it's durable. We also wanted some interesting accents and decided on inlaid aluminum strips, brushed nickel finger pulls, metal legs, and shadow lines between the sides and top/bottom.Because of the painted finish, I decided to build the sideboard entirely from Baltic birch plywood. I thought its void-free composition would let me paint the exposed edges without resorting to edge banding.My wife is really happy with the sideboard, and it fits well with the modern design of our new kitchen.For anyone who is interested, I'll describe some construction details and challenges below. Thanks for looking!Building the CaseI don't build many large cabinets, and I was worried that 1/2” plywood would flex or sag over time. I opted for 1/2” plywood for the sides, but 3/4” for the top, bottom, and vertical dividers.To make the top and bottom look like they were made of 1/2” plywood, I cut rabbets on the front edges (above the drawers and below the doors).I also cut rabbets and dados for joints. That let me easily test-fit the case parts and kept everything aligned during glue-up.I'll talk about this more later, but I painted the interior surfaces before assembly.Because the sides were so thin, I didn't cut dados for the cubby shelf and under-drawer dust panel. I used dowels instead. My new Jessem doweling jig made that job easy. (I don't know if it's possible to love a tool, but this jig makes me think it's possible.)I also used the Jessem jig to drill the shelf pin holes.To strengthen the side/top joints, I added small metal angle brackets. They're hidden by the drawers.I used dowels through the bottom into the sides to reinforce those joints.I opted for a 1/2” back to further strengthen the case. I had to piece it together in sections because of how I had the plywood cut for shipping (and to omit the dado from the back of the cubby).Cutting Dados for the Aluminum Accent StripsI recently built a kerfmaker based on the design from YouTube creator I Simply Built This (https://www.youtube.com/watch?v=uhPvanE9fnc). I have seen several designs, and his is my favorite.This project gave me my first opportunity to use it on a real project. It worked very well. I used it with my table saw to cut all of the dados and rabbets for this project, including the dados for the aluminum inlay on the drawers and door fronts.To use it, I lined up the cut closest to my sled's stop, used the kerfmaker with the tongue extended to set the stop block's position, and made the cut.Then, without moving the stop block, I rotated and moved the kerfmaker so its set screw touched the stop block, moved the work piece to contact the kerfmaker, and made the second cut.Then I just made repeated cuts to remove the remaining material.The only thing that would have made this job easier was a flat top grind saw blade. It took some sanding/scraping to flatten the grooves left by my saw blade.Working with AluminumThe accent strips are 3/8” wide, 1/4” thick 6061 aluminum bar stock from McMaster-Carr.The worst thing about working with it is cleaning it. I used a combination of 150-grit sandpaper and Scotch-Brite pads. It makes quite a mess (very fine dust particles), and I've learned to cover my workbench when cleaning metal to avoid powder stains.Otherwise, it's not too different from wood. I used my table saw to cut the pieces to size, and I used sandpaper to round over the outside ends.Painting (Prefinishing)As I mentioned in the introduction, I don't like painting. I'm hopeless with a brush and only slightly less so with a mini foam roller. I didn't relish the idea of painting the inside of the sideboard after construction, so I decided to paint all of the interior surfaces first.I tested both foam and short nap (1/4”) rollers and got slightly better results from the latter. The main difference was that the short nap roller didn't show pressure/friction marks as easily as the foam roller.This photo is more of a reminder for me if I forget what to use in future projects. I found it at Lowe's.Before priming, I taped off all of the dados and rabbets that would later receive glue. That was very tedious.I applied two coats of Zinsser 1-2-3 primer. It was easy to apply, dried quickly, and sanded well. I don't know if BIN (shellac based) would have been better or not.I used General Finishes Milk Paint (Queenstown Gray) for the finish. I really like this paint. If it ends up being as durable as I hope, it will be my go-to for all future painted projects. It's fairly thick, but it's easy to apply with a roller. (I think those of you who are good with a brush would also like it.) It doesn't stink, and it dries quickly. I applied three coats, waiting two hours and sanding lightly between coats.I'm not sure how I feel about pre-painting. The taping took a long time, and I needed every horizontal surface I had to place the drying panels. In a few places, my tape encroached a bit too far into the cabinet interior, leaving unpainted slivers at inside corners that I had to touch up later. I also had to take a lot of extra care during and after assembling the case to avoid scratching or marring the paint.On the other hand, if I had tried to paint everything after assembly, I'm sure I would have had just as many problems, particularly with a roller.One last note. Earlier, I mentioned choosing Baltic birch plywood so I didn't have to band the edges. That did turn out to be the case. So far, I'm not seeing any plies telegraphing through the paint on the exposed edges.I did rub Zar wood patch over the edges to fill the pores. It came in a tube and squeezed out like very thick toothpaste. I just smeared it on with my finger and sanded it when it dried. It was similar to using joint compound, but it was slightly less messy during sanding.Mounting the HingesI used Blum Euro hinges for the doors. I used my drill press to drill the cup holes and a temporary jig to drill the mounting bracket holes in the sides.The thin sides created a minor headache. The screws that came with the hinges are 5/8” long and were slightly too long for the thin sides. Instead of trying to find and order 1/2” screws, I used my Dremel to cut off the tips.I drilled countersunk holes in a piece of 1/2” scrap and drove the screws. Then it was easy to cut the screws to length.Building the DrawersIn the past, I've used pocket screws to assembly my drawer boxes. For this project, I used my doweling jig. It was just as quick and easy, and it looks better.Mounting the Finger PullsThe finger pulls look nice, but they're a bit of work to mount because they require mortises on both the edge and back of the drawer face or door.The edge mortises are just very shallow dados, so I used my table saw and kerfmaker to cut them. I couldn't do that for the back mortises, so I made temporary jigs and used my router and pattern bit. After that, I cleaned up the mortise corners with a chisel.The pulls are mounted on the top inner edge of the doors, so I butted the doors together and cut the mortises for both at the same time.The drawer pulls are mounted in the centers of the top edges of the drawer fronts, so I had to cut them separately, but I used a similar jig.When I installed the door pulls after painting, I wished that I had cut them slightly wider than necessary. Because of the thickness of the paint or slightly out-of-center screw holes, the pulls protruded slightly from the door edges and contacted each other. I had to slightly widen the back mortises to eliminate that contact.Securing the Adjustable ShelvesThe main cavity is divided in half vertically, and there's an adjustable shelf in each half. I used dowels as hinge pins, and I didn't want the shelves to slide. To ensure that, I routed short, 5/16” wide slots in the shelf bottoms. When the shelves are in place, those slots wrap around the dowels to secure the shelves. The slots will also work with metal shelf pins if I rotate them slightly.Mounting the Metal LegsThe legs we selected (Peter Meier 556 in brushed steel) have five-hole mounting plates. To simplify drilling the screw holes, I built a jig. I drilled holes through the jig with my drill press to make sure they were perfectly perpendicular so I could flip the jig upside down as needed.

Comments:
0 comments, click here to add the first

Dump Truck - Maple and Walnut

Furnished content.
(from Lumberjocks.com)


Made all the parts except the lights and axles.

Comments:
0 comments, click here to add the first

Storage Shed

Furnished content.
(from Lumberjocks.com)


Not fine wood working, only basic construction in this project. :-)Like everyone in world, needed more storage space. If you read my blog, already know was forced to downsize and moved into this rental home late last year. Decided to build a portable 6×12 shed that could be moved easily when time comes. Making it portable added requirement for solid base, and keeping things light but strong.
Shed size is small enough that no permits were required. Only caveat was HOA requirement to color match house/trim.Base is 14ga 2×3 steel frame welded. Size is 2” smaller than inside of a U-haul 6×12 trailer. Welded a couple pulling eyes on front end to enable dragging it out of side yard.

.
After welding, painted with frame with enamel to increase longevity.

.
Glued and screwed down 3/4” pressure treat plywood to complete base. Picture at top shows base leveled on some patio stones in final installation location.Used simple 2×4 framing for walls, glued and screwed into metal base frame. Walls were glued and nailed with T1 siding, and radiant foil barrier OSB for roof. Roof uses tabbed shingles on 3 pitch slant roof. Since AZ doesn't have freezing rain and ice dam issues, didn't need to use roll roofing common despite the low pitch.A weight saving feature on the shed is trim wood. Used 1/4 thick cedar siding, that was ripped to standard width. This kept the shed to my portable size constraints, and reduce the overall weight.Construction was completed with base pushed away from house wall by 4ft (pictured at top), and when completed was able to use 2×6 as lever bar to slide it over into final position. Shed feels like similar weight as pushing my 900lb 20” planer around shop? LOLBefore I closed up interior walls with fire rated OSB, wired the shed with small sub-panel. It is fed by a 50A RV circuit using extension cord and locking plugs to solve the lack of power issues in side yard. Picture of power panel is at the top as well.In the future, if this shed were used next to the garage, the power panel would let me use the shed as compressor and dust collector out building. Shed has 2 GFCI circuits with inside/outside receptacles, an inside overhead light, outdoor security light, plus a 30A 240v receptacle for my welder. There is also enough power to run a mini-split and PC/TV for when SWMBO kicks me out of house and I have to live in there. Wife calls it my 'he shed' as all it needs is to have trailer bolted underneath, and it's a tiny house. :-)Have built several sheds in past. Normally they take 2-4 weeks? This build was agonizingly slow to finish, built over ~4 months total. Primary issue was only working a couple days a week. It was started at end January, right before Covid-19 shelter orders were given. Then my son and wife descended upon the home 24/7 and my quiet retirement life become complicated. One limit was when I could make construction noise outside the new home office(s). My ongoing health challenges also limited overall shop time.The inside of shed was painted white, but I forgot to take photo before I moved stuff into shed.
Learned recently that thanks to the 4ft led fixture inside, and led spot lights on front of shed; I can see well enough to work in side yard after dark. So adding the power panel provided flexibility I had not planned. :-)Thanks for reading and Have a Great Day!Long live the real Captain Klutz (Mad Magazine)!

Comments:
0 comments, click here to add the first